Download xml transmitter pro

To create the return and see below for submitting to Revenu Québec.Submitting T4, T4A and summaries to the CRATo send your T4 reports electronically, click on the Download XML FILE link to download the file necessary for electronic submission to the CRA. Now visit the CRA site and log in to the 'My Business' portal and navigate to the PAYROLL area and tap/click 'File a return':Select 'Internet File Transfer':Upload your file:You'll receive a verification notice from the CRA site:Submitting RL-1 forms and summaries to Revenu QuébecGenerate your RL-1 slipsEnter your company RL-1 summary detailsDownload the RL-1 XML file / PDF if you are submitting the data directly to Revenu Quebec.Alternatively, if you have entered an XML submitter number in your RL-1 summary details, you can submit directly click on step 5. **NOTE this option will only submit employee slips, you still need to submit your company summary to Revenue Quebec.(OPTIONAL if you have not submitted directly through payroll profile) Visit the Revenu Québec site to transmit your RL-1 slips online. Tap 'Access Service':Follow the on screen prompts to submit your XML file. You'll need your transmitter number and business identification number. If you do not have these, you can apply for them from the site directly.After you submit your slips electronically download the PDF file of the RL-1 Summary and mail this in to Revenu Quebec.PLEASE NOTE: In order to submit RL slips electronically, each business requires a transmitter number. This transmitter number may vary from year to year. You should receive this number directly from Revenu Quebec. Existing businesses who have submitted RL forms to Revenu Quebec in the past will also have received slip numbers. You will need your transmitter number and your slip number to submit your RL forms.To obtain a transmitter number, please visit the Revenu Quebec site and submit an ED-430-V form. Revenu Quebec will then respond with your transmitter number.Accessing T4, T4A, RL-1 reports after submittingOnce you've created the T4 and other reports, you can always go back the REPORTS area and select T4 Reports to view/print/download the PDF and XML file again. PLEASE NOTE: The PDF and XML versions are only available if you are on a paid payroll plan. Related articles Création des T4s, T4As et les RL-s RL-1 Company Summary Guide PD27 and your T4 Summary Automatic vacation calculations

Compatible with Hi-Sync? What is ODS? ODS means Over Drive Sync in Hi-Sync mode.It enables to fine-tune the Transmitter Pro trigger signal to optimize exposure at high shutter speeds while gaining more light.The ODS Setup offers adjustment from 0.1 to 5.0 ms or can be switched off.The ODS value will vary depending on the camera and the flash unit used, and must be adjusted manually. Elinchrom and Phottix (Odin II) Odin II is one of the two remote options in the ELB 500 TTL settings menu.When this remote option is enabled, the ELB 500 TTL is compatible with Phottix Odin II transmitters and Phottix products with built-in Odin II or with Phottix Odin II receivers.Only available for Canon and Nikon. Hi-Sync compatibility Some units are compatible with Hi-Sync, others not.Please check the compatibility page for more information. Change ID unit number It is not possible to change the flash unit ID numbers.The ID number is unique to each product and currently unchangeable.But you can give a custom name directly from the Elinchrom App / Software. How to reset the Transmitter Pro to default settings? Push the left and right speed buttons while the Transmitter is ON (approximately 2 seconds).This will reset the Transmitter Pro to manufacture settings.All user settings, except the display contrast, will be reset. Transmitter Pro firmware update The firmware of the Transmitter Pro can be updated via the mini USB socket.Please download the Elinchrom Updater software. Transmitter triggering problems Please verify the following points:Transmitter and receiver must have the same frequency channel settings.Transmitter and receiver must have the same synchronization mode settings: Normal or Speed sync mode (ELSP MODE on the Transmitter Pro).Check that the EL-Skyport receiver in all EL units with built-in receivers is switched ON.Try another frequency channel for both transmitter and the receiver of the Elinchrom unit.Reduce the distance between the flash unit and transmitter.Check the hotshoe fitting.Check the camera settings (turn hotshoe communication on).Check that the Transmitter Pro version corresponds to your Canon, Nikon, Sony, or Fujifilm camera.Check the list of compatible cameras.Learn more about Speed and Normal sync mode. Transmitter distance range The distance range of the Transmitter Plus or Pro is 200 m (656 feet) outdoors and 60 m (196 feet) indoors.If the distance is limited, then please try the following:Reposition the units.Increase the distance from walls and ceilings.ELSP Mode:In speed sync mode the distance range is reduced by approximately 50%, switch back to Normal sync mode.Outdoors, the distance range could be reduced due to humidity, interference, obstacles, etc. Change power from the Transmitter is not working Please make sure your Elinchrom unit and Transmitter are both updated with the latest firmware.www.elinchrom.com/support/firmware Use a Transmitter Pro for Canon on a Nikon camera and reverse Yes, you can use it but in manual mode only.Only the hot-shoe middle contact is available to trigger Elinchrom flash units.You can use a Canon Transmitter Pro on a Nikon camera or a Nikon Transmitter Pro on a Canon in manual mode.You can still control power and

[NR] admin | Published: November 21, 2018 Nikon released new software updates for Wireless Transmitter Utility, Camera Control Pro 2 and ViewNX-i/Capture NX-D:Wireless Transmitter Utility Version 1.8.1Added support for the Z 6.Added support for macOS version 10.14 (Mojave).Ended support for OS X version 10.11.Camera Control Pro 2 Version 2.28.0This software is for current owners of Camera Control Pro 2. For new users, it functions as a trial version that, once installed, can be used for up to 30 days before purchase is required.This software is distributed as a file named “S-CCPRO_-022800MF-ALLIN-64BIT_.dmg”. Download and run the file to perform the update.When performing the update, you may be required to enter the product key to confirm ownership.Before beginning installation, exit Camera Control Pro 2 and all other applications, including any anti-virus software.When performing the update, you will be prompted for the administrator password.The interface after the update will be in the same language as the current software and cannot be changed.If you are using D5 “C” firmware version 1.20 or later, update Camera Control Pro 2 to the current version, as versions 2.25.0 or earlier will not function as expected.This update may result in Wireless Transmitter Utility versions 1.5.6 or earlier being unable to detect the camera in some versions of OS X. Users of the Wireless Transmitter Utility should install version 1.6.0 or later.Read the information below before proceeding.ViewNX-i & Capture NX-D Version 1.18.040No new changes, this package installs Nikon’s free ViewNX-i and Capture NX-D software and updates it to the latest version.