Easy line remote

4 subnets, 2 masks! The next line is the Easy VPN router (ezvpn2).S 10.75.2.2/32 [1/0] via 10.76.1.1! The next line is the Easy VPN router (ezvpn1).S 10.75.1.2/32 [1/0] via 10.76.1.1C 10.76.2.0/24 is directly connected, Serial2/0C 10.76.1.0/24 is directly connected, Ethernet1/0C 192.168.1.0/24 is directly connected, Ethernet0/0! The next line is the Easy VPN route (ezvpn1).S 192.168.3.0/24 [1/0] via 0.0.0.0, Virtual-Access2! The next line is the Easy VPN (ezvpn2).S* 10.0.0.0/0 [1/0] via 10.0.0.0, Virtual-Access3 The route to split tunnel "192.168.3.0/24" that points to Virtual-Access2 is added for the Easy VPN "ezvpn"" tunnel as shown in the above show output. Reactivate Primary Peer Example The following show output illustrates that the default primary peer feature has been activated. The primary default peer is 10.3.3.2. Router# show crypto ipsec client ezvpn Easy VPN Remote Phase: 6Tunnel name : ezcInside interface list: Loopback0Outside interface: Ethernet0/0 Current State: IPSEC_ACTIVEPrimary EzVPN Peer: 10.3.3.2, Last Tried: Dec 30 07:21:23.071Last Event: CONN_UPAddress: 10.7.7.1Mask: 255.255.255.255DNS Primary: 10.1.1.1NBMS/WINS Primary: 10.5.254.22Save Password: DisallowedCurrent EzVPN Peer: 10.4.4.223:52:44: %CRYPTO-6-EZVPN_CONNECTION_UP(Primary peer): User: lab, Group: hw-client-g Client_public_addr=10.4.22.103, Server_public_addr=10.4.23.112 Assigned_client_addr=10.7.7.1 Identical Addressing Support Configuration Example In the following example, a Cisco router is configured for the Identical Addressing Support feature: interface Virtual-Template1 type tunnel no ip address ip nat outside!crypto ipsec client ezvpn easy connect manual group easy key work4cisco mode network-extension peer 10.2.2.2 virtual-interface 1 nat allow nat acl 100!interface Ethernet1/0 ip address 10.0.0.1 255.255.255.0 ip nat outside crypto ipsec client ezvpn easy !interface Ethernet0/0 ip address 10.0.1.1 255.255.255.0 ip nat inside !interface Loopback0 ip address 10.1.1.1 255.255.255.252 ip nat enablecrypto ipsec client ezvpn easy inside!ip access-list 100 permit ip 10.0.0.0 0.0.0.255 any!ip nat inside source list 100 interface Loopback0 overload cTCP on an Easy VPN Client (Remote Device) Examples For configuration and troubleshooting examples, see the topic "cTCP on Cisco Easy VPN remote devices" in the cTCP on an Easy VPN Client (Remote Device) Examples. Easy VPN Server Configuration Examples This section describes basic Cisco Easy VPN server configurations that support the Cisco Easy VPN remote configurations given in the previous sections. For complete information on configuring these servers, see Easy VPN Server for Cisco

The new Easy Line Remote offers improved functionality and a sleek new design, providing a seamless and personalized hearing experience. With this remote, you have access to a range of enhanced hearing controls and personalization options for your hearing aids, as well as the ability to track your health data.The Remote Control feature allows you to easily make adjustments to your hearing aids based on your preferences for different listening situations. You can effortlessly adjust the volume and various features of your hearing aids, such as noise reduction and microphone directionality. You can also choose from pre-defined programs designed for specific listening environments. Furthermore, you have the option to fine-tune the sound equalizer using preset options or personalized adjustments using sliders for bass, middle, and treble.The Remote Support feature enables you to connect with your hearing care professional through a live video call and have your hearing aids adjusted remotely, with appointments available.Within the Health section of the app, you'll find numerous functions, including tracking your steps and wearing time. Optional goal setting and activity level tracking are also available.Please note that certain features may be only available on specific models such as KS 10.0 and Brio 5.In addition, the Easy Line Remote allows you to configure Touch Control settings, set up cleaning reminders, and access additional information such as battery level and the status of connected hearing aids and accessories.When it comes to compatibility, the Easy Line Remote is compatible with a range of hearing aids including KS 10.0, KS 9.0, KS 9.0 T, Brio 5, Brio 4, Brio 3, and Phonak CROS™ P (KS 10.0). It is also compatible with iPhone 6s and newer devices running iOS Version 14.0 or higher. For verification of smartphone compatibility, please visit our compatibility checker on the following link: Compatibility Checker.For detailed instructions, please refer to the Instruction for Use available at Instruction for Use.Please note that "IOS" is a trademark of Cisco, Inc., and the Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc., used under license by Sonova AG.Remember to always consult a doctor for medical advice in addition to using this app, and ensure that the app is available in countries where the compatible hearing instruments have received official approval for distribution. Additionally, Easy Line Remote supports integration with Apple Health when connected to a compatible hearing aid, such as Phonak Audéo Fit.Easy Line Remote

Route 0.0.0.0 0.0.0.0 ATM0ip route 0.0.0.0 0.0.0.0 Dialer1 permanentip route 10.0.0.0 255.0.0.0 10.0.0.13ip http serverip pim bidir-enable!line con 0 stopbits 1line vty 0 4 login!scheduler max-task-time 5000 Cisco Easy VPN Client in Network Extension Mode (Cisco 1700 Series) Example In the following example, a Cisco 1700 series router is configured as an Easy VPN remote using the Cisco Easy VPN Remote feature in the network extension mode of operation. This example shows the following components of the Cisco Easy VPN remote configuration: Cisco Easy VPN Remote configuration--The first crypto ipsec client ezvpn command (global configuration mode) creates a Cisco Easy VPN remote configuration that is named "easy vpn remote." This configuration specifies the group name "easy vpn remote-groupname" and the shared key value "easy vpn remote-password," and it sets the peer destination to the IP address 10.0.0.2 (which is the address assigned to the interface connected to the Internet on the destination peer router). The Cisco Easy VPN remote configuration is configured for network extension mode. Note If DNS is also configured on the router, the peerkeyword option also supports a hostname instead of an IP address. The second crypto ipsec client ezvpn easy vpn remote command (interface configuration mode) assigns the Cisco Easy VPN remote configuration to Ethernet 0 interface so that all traffic that is received and transmitted on that interface is sent through the VPN tunnel. !version 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryption!hostname 1710!!mmi polling-interval 60no mmi auto-configureno mmi pvcmmi snmp-timeout 180ip subnet-zero!!ip ssh time-out 120ip ssh authentication-retries 3!!ip dhcp excluded-address 10.0.0.10 !ip dhcp pool localpool import all network 10.70.0.0 255.255.255.248 default-router 10.70.0.10 lease 1 0 0 !!crypto ipsec client ezvpn easy_vpn_remote group easy_vpn_remote_groupname key easy_vpn_remote_password mode network-extension peer 10.0.0.2!!interface Ethernet0 ip address 10.50.0.10 255.0.0.0 half-duplex crypto ipsec client ezvpn easy_vpn_remote!interface FastEthernet0 ip address 10.10.0.10 255.0.0.0 speed auto!ip classlessip route 10.20.0.0 255.0.0.0 Ethernet0ip route 10.20.0.0 255.0.0.0 Ethernet0no ip http serverip pim bidir-enable!!!line con 0 exec-timeout 0 0line aux 0line vty 0 4 login Save Password Configuration Example The following sample show running-config output shows that the Save Password feature has been configured (note the

Please carefully follow the instructions in the app or the following steps: 1. Please install the app from the App Store.2. On your smartphone open the Easy Line Remote app and click “Continue”.3. Walk through the “welcome screens”.4. Please read and “Accept” the Privacy Notice.5. If you like, you can share usage data with us. You can find the details in the Privacy Notice of the app.6. Make sure that Bluetooth® is enabled on your iPhone®.7. Reboot the hearings aids following the instructions in the app.8. On the Easy Line Remote app tap “Continue” to search for the hearing aids. 9. The Easy Line Remote app will start searching for the hearing aids.10. Once they are found tap “Connect.”11. Allow the app time to connect to both hearing aids and confirm the action for each hearing aid in the dialog.12. After the hearing aids are connected tap “Continue”.13. Congratulations! Once completed you’ll see a confirmation screen and will be automatically redirected to the main screen.Please note: you only have to do the onboarding and pairing once, afterwards the hearing aids connect automatically when you open the app.

12:48:17.267: EZVPN(tunnel22): Received authentic disconnect credentialDec 10 12:48:17.275: EZVPN(): Received an HTTP request: disconnectDec 10 12:48:17.275: %CRYPTO-6-EZVPN_CONNECTION_DOWN: (Client) User= Group=tunnel22 Client_public_addr=192.168.0.13 Server_public_addr=192.168.0.1 Assigned_client_addr=10.3.4.5 The following output from the two show commands (show crypto ipsec client ezvpn and show ip auth-proxy config) displays what you might see before a user is connected to a VPN tunnel: Router# show crypto ipsec client ezvpn tunnel22Tunnel name : tunnel22Inside interface list: Ethernet0Outside interface: Ethernet1Current State: CONNECT_REQUIREDLast Event: RESETSave Password: Disallowed! Note the next line. XAuth credentials: HTTP intercepted HTTP return code : 200 IP addr being prompted: 0.0.0.0Current EzVPN Peer: 192.168.0.1Router# show ip auth-proxy configAuthentication global cache time is 60 minutesAuthentication global absolute time is 0 minutesAuthentication Proxy Watch-list is disabledAuthentication Proxy Rule Configuration! Note that the next line is the Easy VPN-defined internal rule. Auth-proxy name ezvpn401*** Applied on Ethernet0 http list not specified inactivity-timer 60 minutes The following output from the two show commands (show crypto ipsec client ezvpn and show ip auth-proxy config) displays what you might see after the user has been connected to the tunnel: Router# show crypto ipsec client ezvpn tunnel22Tunnel name : tunnel22Inside interface list: Ethernet0Outside interface: Ethernet1Current State: IPSEC_ACTIVELast Event: SOCKET_UPAddress: 10.3.4.5Mask: 255.255.255.255Save Password: Disallowed XAuth credentials: HTTP intercepted HTTP return code : 200 IP addr being prompted: 192.168.0.0Current EzVPN Peer: 192.168.0.1Router# show ip auth-proxy configAuthentication global cache time is 60 minutesAuthentication global absolute time is 0 minutesAuthentication Proxy Watch-list is disabledAuth-proxy name ezvpnWeb*** (EzVPN-defined internal rule)http list not specified inactivity-timer 60 minutes Troubleshooting the VPN Connection Troubleshooting a VPN Connection Using the Cisco Easy VPN Remote Feature Troubleshooting the Client Mode of Operation Troubleshooting Remote Management Troubleshooting Dead Peer Detection Troubleshooting a VPN Connection Using the Cisco Easy VPN Remote Feature To troubleshoot a VPN connection created using the Cisco Easy VPN Remote feature, use the following suggested techniques. Be aware that any changes to an active Cisco Easy VPN remote configuration or IP address changes to the involved interfaces, such as adding or removing an inside interface, result in a reset of the Cisco Easy VPN Remote connection. Enable debugging of the Cisco Easy

(Cisco 1700 Series) Example Cisco Easy VPN Client in Network Extension Mode (Cisco 831) Example In the following example, a Cisco 831 router is configured as an Easy VPN remote using the Cisco Easy VPN Remote feature. This example shows the following components of the Cisco Easy VPN remote configuration: The Ethernet 0 interface is assigned an address in the network address space of the Cisco IOS Easy VPN server. The ip route command directs all traffic for this network space from the Ethernet 1 interface to the destination server. Cisco Easy VPN Remote configuration--The first crypto ipsec client ezvpn command (global configuration mode) creates a Cisco Easy VPN remote configuration named "easy vpn remote." This configuration specifies the group name "easy vpn remote-groupname" and the shared key value "easy vpn remote-password," and it sets the peer destination to the IP address 192.185.0.5 (which is the address assigned to the interface connected to the Internet on the destination peer router). The Cisco Easy VPN remote configuration is configured for network extension mode. Note If DNS is also configured on the router, the peer keyword option also supports a hostname instead of an IP address. The second crypto ipsec client ezvpn command (interface configuration mode) assigns the Cisco Easy VPN Remote configuration to the Ethernet 1 interface so that all traffic that is received and transmitted on that interface is sent through the VPN tunnel. ! Cisco Router Web Setup Template!no service padno service tcp-small-serversno service udp-small-serversservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname Router!!ip subnet-zeroip domain-lookup!!ip dhcp excluded-address 172.31.1.1 !ip dhcp pool localpool import all network 172.31.1.0 255.255.255.255 default-router 172.31.1.1 lease 1 0 0 !!crypto ipsec client ezvpn easy_vpn_remote peer 192.168.0.5 group easy_vpn_remote_groupname key easy_vpn_remote_password mode network-extension !!interface Ethernet0 ip address 172.31.1.1 255.255.255.255 no cdp enable hold-queue 32 in!interface Ethernet1 ip address dhcp no cdp enable crypto ipsec client ezvpn easy_vpn_remote!ip classlessip route 172.31.0.0 255.255.255.255 Ethernet1ip http server!!line con 0 exec-timeout 120 0 stopbits 1line vty 0 4 exec-timeout 0 0 login local Cisco Easy VPN Client in Network Extension Mode (Cisco 837) Example In the following example, a Cisco