Fan xpert

[Motherboard] Fan Xpert 4 - Introduction Fan Xpert 4 in AI Suite 3 is used to control all the fans that connect to the motherboard, user can adjust rotating speed of fans to customize the need.Starting from the Intel 600 / AMD X670E series, the Fan Xpert functionality will be integrated into Armoury Crate.For motherboards below the Intel 600 / AMD X670E series, please refer to the following instructions to use Fan Xpert:How to use Fan Xpert 4 in AI Suite 3 to control the fan ?1. Open AI Suite 3.2. Click Fan Xpert 4.3. Click Fan tuning to apply the suitable setting on all of fans.4. Tuning proceeding.5. Tuning process is finished when the screen shows Available.6. User can choose default mode: Silent/Standard/Turbo/Full speed from the list. Mode that user choose will apply to all the fans.7. User can also choose one specific fan to set up its rotating speed. Click left/right arrow key to choose the fan.8. Click the diagram to enter the setup.9. Click the Smart mode, and you can move/drag the blue dot to adjust the rotating speed. 10. Under the Smart mode, you can also set up the spin up/spin down time to prevent rotating speed from vast change within a short period of time. Click the Auto-Fan Stop, fan will stop at very low RPMs.11. Click Source, select up to three thermal sources, and the fan speed will automatically change based on the highest temperature.12. Use RPM fix mode, toggle the arrow to set up the rotating speed.13. AI Cooling function is a new feature that applies on ASUS Intel Z490 series motherboard. Al Cooling will decrease the fan rotating speed when system is at stable status.FAQQuestion1: What to do when fan is not working?Step 1: Open Fan Xpert 4 in AI Suite 3, do the fan tuning again.Step 2: Make sure all the cables plug properly.Step 3: Plug another fan to check if the card is working.Step 4: Contact ASUS service center if the steps above are unable to fix the problem. 2: I am unable to set up the rotating speed through Fan Xpert 4.Step 1: Open Fan Xpert 4 in AI Suite 3, and do the fan tuning again.Step 2: Uninstall the AI Suite 3, and install AI Suite 3 again. Refer to the link below for the steps to install and uninstall the AI Suite 3. 3: Which model supports

FAQ [Motherboard] Fan Xpert 4 - Introduction Fan Xpert 4 in AI Suite 3 is used to control all the fans that connect to the motherboard, user can adjust rotating speed of fans to customize the need.Starting from the Intel 600 / AMD X670E series, the Fan Xpert functionality will be integrated into Armoury Crate.For motherboards below the Intel 600 / AMD X670E series, please refer to the following instructions to use Fan Xpert:How to use Fan Xpert 4 in AI Suite 3 to control the fan ?1. Open AI Suite 3.2. Click Fan Xpert 4.3. Click Fan tuning to apply the suitable setting on all of fans.4. Tuning proceeding.5. Tuning process is finished when the screen shows Available.6. User can choose default mode: Silent/Standard/Turbo/Full speed from the list. Mode that user choose will apply to all the fans.7. User can also choose one specific fan to set up its rotating speed. Click left/right arrow key to choose the fan.8. Click the diagram to enter the setup.9. Click the Smart mode, and you can move/drag the blue dot to adjust the rotating speed. 10. Under the Smart mode, you can also set up the spin up/spin down time to prevent rotating speed from vast change within a short period of time. Click the Auto-Fan Stop, fan will stop at very low RPMs.11. Click Source, select up to three thermal sources, and the fan speed will automatically change based on the highest temperature.12. Use RPM fix mode, toggle the arrow to set up the rotating speed.13. AI Cooling function is a new feature that applies on ASUS Intel Z490 series motherboard. Al Cooling will decrease the fan rotating speed when system is at stable status.FAQQuestion1: What to do when fan is not working?Step 1: Open Fan Xpert 4 in AI Suite 3, do the fan tuning again.Step 2: Make sure all the cables plug properly.Step 3: Plug another fan to check if the card is working.Step 4: Contact ASUS service center if the steps above are unable to fix the problem. 2: I am unable to set up the rotating speed through Fan Xpert 4.Step 1: Open Fan Xpert 4 in AI Suite 3, and do the fan tuning again.Step 2: Uninstall the AI Suite 3, and install AI Suite 3 again. Refer to the link below for the steps to install and uninstall the AI Suite 3. 3: Which model supports AI Cooling function?Answer 3: ASUS Intel Z490 series motherboards supports AI Cooling function.Question 4: Is all fan headers on the motherboard support AI Cooling?Answer 4: Fans need to be connected to the following headers for Al Cooling control: CPU_FAN / CPU_OPT / CHA_FAN / M.2_FAN / H_AMP / RAD_FAN,

Board Software Software needs to be installed using Armory Crate and this posed a problem. The software on the USB flash drive refused to install properly while the installer obtained from the product page seemed to have problems installing Fan Xpert 4. In the end we had success by downloading the entire 4 GB Armoury Crate package from this link but even then several sections of the suite refused to install without updates, many of which seemed non-existent or took an age to download and install. With a 1 Gbit download speed we have confidence this was the software or an issue with the ASUS servers and not our Internet connection, but eventually we got there.The primary reasons you'd want to install any of the software are Aura Sync for configuring and synchronizing your GB lighting across the motherboard, any attached LED devices and compatible components and also Fan Xpert 4. Honestly, we'd rather have Fan Xpert 4 available as a standalone software as it does give you one of if not the best Windows-based fan control suites of any manufacturer, with the ability to fine tune fan curves, switch between smart and fixed RPM modes and even pick from alternative temperature inputs for system and pump fans such as thermal or coolant probes, which is extremely useful for situations involving watercooling. At the very least it's useful for configuring your fan speeds within Windows using your preferred stress tests, which is obviously not possible from the EFI BIOS.

Core,Asus GTX 580, 844 MHz core,Multiple WD HDDs: 2TB Black Hybrid,2TB Black,1TB Green,4TB RE4,2x-1TB Velociraptor,OCZ Z Series 1000w,Coolermaster Hyper 612 PWM, Fractal Design Define R4System is a Photoshop/Lightroom workstation. Otherwise runs Great Internet Mersenne Prime Search 24/7. Prime 95 on CPU, mfaktc Trial Factoring on GPUs Unfortunately these boards are kinda limited in fan control. Your right with the opt fans, chassis fans can be done with fan xpert but all together, not individually like i had hoped and the cpu headers can also be controlled in fan xpert but they to are controlled together, what ever fan curve u set, it applys to all associated headers even if there different things on them. I even tried the program speed fan but no dice on my formula z board PSU: Antec Platinum 1000wattCPU: AMD FX-9590 currently, 1100T BE still around CPU cooler: Swiftech H320Mobo: Crosshair V formula-Z Bios 2101Ram: Kingston hyper x beast 16gb [KHX18C10T3K2/16X]VGA: 2x Gigabyte GTX 670 2gb WF3 ocCase: Cooler master HAF-XKeyboard: Logitech G710+Mouse: Logitech G700sScreen: Asus VG248QEHdd 1: SanDisk 240gb OSHdd 2: OCZ agility 3 60gbHdd 3: WD Black 1tbOptical drive: Asus dvd\blue ray cheapyOS:Win 7 home